PULL STUDS CODE NO.
:NC5 Spindle Available
Machine Maker
Machine Model
TAPER Holder Code No.
TV -300, 400 ACCUMILL 4000 ULTIMILL H3000, V3000 MILLTAP 700 MAX 3000 Centre Through SV, SH, SLV, MV, MH, NV, NMV, NVD, NH, AFM, Dura Vertical, NVX, NHX, VS, NT series Super TILT 500 SVL 5000, 5250 Centre Through SV 400 SV 500 SH 50 SH 500 SV, SH, MV, MH, MB, NV, NH, NVX, NHX, VS, NMH, NMV, NT series MV 1003 MV 65B/50 duo BLOCK series duo BLOCK series Centre Through VK series VM -40, 50 VS -40, 50, 60 VKC series VA series HG -400 HS series HK -630 HA series VS- 50, 60 Centre Through VS -40, 50, 60, HG - 800 VK -45, 55, 65, 85 VA series VG series VF series VS -50, 60 HS series HK -630 HG series HC series HS -630 HG -630 VF -23 VK -85 Centre Through IMPULSE 30 Type A , B , C UN -600V, 600H VTC, V, VQC, AJV, FJV, FH, FF, VARIAXIS, NEXUS, INTEGREX, VCN, HCN, PFH, μ series ANGULAX 900 FF -510, 660 VTC, V, VQC, AJV, FJV, SV, H, FH, MTV, HV, INTEGREX, VORIEX, VARIAXIS, VCN, HCN, VERSATECH, μ series H -12, 12N, 15, 20, 25 V 12, 15, 20 VQC -10/15, 20/50 YBM, YPC, VPC series H 30i H 40 VBMV i40 Centre Through YBM, YMC series Centre Through YBM -700N, YBM -120N
No.30 30 40 40 40 40 50 50 50 No.40 40 40 40 No.40 40 40 45 50 50 50 No.30 40 40 50 50 No.40 40 40 50 50 50 No.30
PS-16
BT30 30 40 40
-114 -O8-1
-366E-1 -N63AE -N63VE -0 -N100VE -835 -366-D7 -309 -N63AE -H28 -N85VE -0 -G58 * 1 -N63AE -G45 * 1 -G4 -805 -854 -5 -563 -N100VE -N100 -048B
NC5-63 NC5-63 BT50 NC5-100 -100 BT40 IT40 BT40 IT40 BT40 NC5-63 BT40 NC5-85 BT50 NC5-100 BT50 BT30 40 NC5-63 BT50 50 BT40 40 40 50 50 NC5-100 BT30 NC5-46 NC5-46 BT40
DMG MORI SEIKI
PS-366 -302
PS-1
PS-17
YAMAZAKI MAZAK
PS-1
YASDA
LIBERO RX series LIBERO RX series GIGA LIBERO RX series KX, MX, LX, GR -655N VERTIMAC series RM series GIGA
PS-16
30 30 40
-110 -N46E -1
ROKU-ROKU
★ This table shows the standard Pull Stud Code No. for the newest M/C. Please refer old NIKKEN catalogue for the Pull Stud of the old M/C. ★ The Pull Stud Code No. depends on your M/C specification, therefore please check your M/C specification to select the proper Pull Stud. ★ ＊ 1 Please order the pull stud Code No. of MAZAK P.320
This is typical information (guide line) of the stopper pin only for the Spindle Speeder and Oil Hole Holder. Be careful that the dimension of the stopper pin for Angular Head is different from this. Please refer your M/C specification very carefully for more detail. TECHNICAL INFORMATION for STOPPER PIN
H
φ E
φ E
H 2 Dimension at free Fig.1
+ θ
− θ
Dimension at free Fig.2
H 2
H E H 2
H E H 2
Fig.
Fig.
Shank
Shank
Machine Maker
Machine Maker
1 1 1 1 1 1 2 2 1 1 1 1 2 2 2 2 2 2 2 1 1
14 22 12 14 -1 29
12 18 12 12 12 12 18 18 12 18 12 18 18 18 18 18 18 18 18 12 18
60 82 40 60 55 55 65 80 60 82 60 82 65 80 65 80 65 80 65 60 82
BT40 50 BT30 40 BT30 BT30 BT40 50 BT40 50 BT40 50 BT40 50 BT40 50 BT40 50 BT40 BT40 50
1 1 1 2 2 2 2 1 1 2 1 1 2 1 2 2 2 2 2 2
4 14 22
12 12 18 18 18 18 18 12 18 18 18 12 18 18 18 24 18 18 18 18
50 60 82 65 80 65 80 65 82 65 82 60 145 82 65 145
BT30 40 50 BT40 50 BT40 50 BT40 50 BT40 50 BT40 50 BT50 BT40 50 BT40 50 BT40 50
DMG MORI （ HITACHI SEIKI ） BROTHER KIRA FANUC MAKINO
ENSHU
0 0 0
OKUMA
OKUMA HOWA
2 5
11 16 22 0 22 14 0 22 0 24 0 4 0 11
NIDEC OKK
28 22 14 22 0 27.7
MATSUURA
KITAMURA
MITSUI SEIKI
KURASHIKI SHIN NIPPON KOKI （ SNK ） TOSHIBA
MITSUBISHI
4 0 2 0 9
DMG MORI
65 80 65 80
JTEKT
YAMAZAKI MAZAK ROKU-ROKU
NIIGATA
14 22
YASDA
323
Powered by FlippingBook