HSK HIGH SPEED SPINDLE SPEEDER
10,000 ～ 40,000r/min ■ NIKKEN NX increases the spindle speed by 4 to 10 times, so economically convert your standard M/C to high speed M/C. ■ Even small endmills can cut smoothly without chatter. ■ Run-out accuracy is more stable due to TiN Bearing Nut (standard accessory).
SK Collet
Within 10microns
H
HSK-PX
φ D
φ C
φ D
φ C1
HSK40 Explanation of the Code No. PX 5 160
4D
ℓ
L
Length
Ratio
NX : 4times, 5 times PX : 6times, 10 times
Shank
Weight （ kg ） 4.1 4.5 6.8 7.2
HSK63A HSK100A TAPER Code No. PX type ★ Grease lubrication is standard. HSK 63A-PX 6-150GX -PX10-160GX HSK100A-PX 6-150GX -PX10-160GX
D
L 151 160.5 147 171.5
C
76 98 76 98 C 1
H
6 10 6 10 Ratio
30,000 40,000 30,000 40,000 MAX. r/min
Collet
60
0.5 ～ 8.0
ETS14
22
14.5
82
Air Cylinder for Cooling with ON/OFF Magnet NXE-COOL The best cooling is to cool the speeder body directly.
★ Please add “ MX ” instead of “ GX ” at the end of Code No. for the oil mist lubrication. e.g. BT40-PX6-130MX ★ ETS collet is supplies as an option.
ETS Explanation of the Code No. 14 0.5
ETS Collet
★ φ d=0.5 ～ 1.0: Each 0.1mm (Gripping range : 0.1mm) e.g. ETS14-0.5 : 0.4 ～ 0.5mm ★ φ d=1.25 ～ 2.5: Each 0.25mm (Gripping range : 0.25mm) ★ φ d=3.0 ～ 8.0: Each 0.5mm (Gripping range : 0.5mm)
φ d
MAX. Chucking Dia.
Style No.
φ 14.5
Symbol of ETS Collet
20.5
X-Treme Shank HSK X-Treme Chuck
C32EX Explanation of the Code No. HSK100A 121
L
J
ℓ 2
J: J-Type (Jet Groove)
Nominal Gauge Length
Chucking Capacity X-Treme Chuck Symbol of Milling Chuck
φ C 1 φ D
Shank No.
Centre Through MAX. 7MPa
JAPAN, USA, EU, CHINA PAT.
End mill with oil hole
Weight (kg)
Handle (Option)
Code No.
ℓ 2 58 68 71 58 68 71
TAPER
C 1
L
（ φ D - L ）
Stopper ＊
Face cap ＊
9MC12HEX- 6L 9MC16HEX-6.5L 9MC20HEX- 7L 9MC12HEX- 6L 9MC16HEX-6.5L 9MC20HEX- 12L 9MC25HEX-6.2L 9MC32HEX- 7L 9MC42HEX- 9L 9MC20HEX- 12L 9MC25HEX-6.2L 9MC32HEX- 7L 9MC42HEX- 9L
9C12SL-FS-EX-A1 9C16SL-FS-EX-A1 9C20 -FS-EX-A1 9C12SL-FS-EX-A1 9C16SL-FS-EX-A1 9C20 -FS-EX-A1 9C25SL-FS-EX-A1 9C32SL-FS-EX-A1 9C42SL-FS-EX-A1 9C20 -FS-EX-A1 9C25SL-FS-EX-A1 9C32SL-FS-EX-A1 9C42SL-FS-EX-A1
GH16 GH20 GH25
HSK 63A-C12EX- 96 -C16EX-101 -C20EX-106 HSK100A-C12EX- 96 -C16EX-106 -C20EX-116 -C25EX-116 -C32EX-121 -C42EX-136 HSK125A-C20EX-121S
40 48 55 40 48 55 55 68 86 55 55 68 86
96 101 106 96 106 116
1.3 1.5 1.7 2.7 3.0 3.6 3.5 4.0 5.7 5.4 5.3 6.3 7.1
HSK63A
GH16 GH20 GH25 GH25 GH32 9HC42 GH25 GH25 GH32 9HC42
HSK100A
116.3 121.3 136 121 121.3 136.3 136
76.3 83.3 86 71 77.3 83.3 86
-C25EX-121S -C32EX-136S -C42EX-136S
HSK125A
Please use direct chucking without KM collet. ★ MAX. 7MPa of center through coolant is available with the stopper. ★ Please use J -type X-Treme chuck, when end mill without oil hole is used. eg) HSK125A-C32EX-136S-J In case of J -type X-Treme chuck, J -type stopper and J -type face cap (with Jet grooves) are attached. 9MC32HEX-7L-J, 9C32L-FS-EX-J1 J -type X-Treme chuck is used for the pocket milling and side milling.
GH Handle P.299
272
Powered by FlippingBook