HSK SLIM CHUCK
GNo. （ Option ）
H
φ C
φ C 1
φ C
φ D
GNo. （ Option ）
ℓ
ℓ 1
H
Fig. 2
L
GNo. （ Option ）
φ C
φ C
φ D
H
Centre Through MAX. 7MPa SK
φ C
ℓ
φ C 1
φ C
φ D
Fig. 1
L
ℓ
ℓ 1
Fig. 3
L
・ Please add “ -J ” at the end of code No. for the chuck with SK J type nut. （ Cap is not included, please order separately ） e.g. HSK63A-SK10C-105P-J JAPAN, USA, EU, KOREA PAT. ・ When SK J type nut is used, the total chuck length will be extended by 6mm. ・ When using SK-A collets or SK-AC collets, or when gripping a cutting tool smaller than the nominal diameter on SK collets, the total length will be shortened by about 3 mm. Please be careful when you check the interference.
G No. （ Option ）
Weight （ kg ）
φ D H H 1 ℓ
ℓ 1
Code No.
C 1
TAPER
C
Fig. SK Collet
0.7 ～ 6.0
26 ～ 31
HSK100A -SK 6C-105 -SK10C-105 -SK10C-120 -SK10C-150 -SK10C-200 -SK13 -105 ＊ 3
2
SK 6
SKG6-6HG
46
62 57 74 80 75 71 86 92 92 71 86 90 90 86
71 71 86
19.5
40
1.2 2.6 2.9 3.2 3.5 2.7 3.1 3.4 3.8 2.7 3.2 3.5 3.8 3.1 3.5 4.2 3.4 4.8
40
1.75 ～ 10.0
33 ～ 41
2
SK10
SKG10-10HG
58
27.5
116 166 - 116 166
39 - 45 45
63
-
63
1 2 3 1 2 3
-SK13C-120 -SK13C-150 -SK13C-200 -SK16 -105 ＊ 3 -SK16C-120 -SK16C-150 -SK16C-200 -SK20C-120 -SK20C-150 -SK20C-200 -SK25 -120 ＊ 3 -SK25C-145
2.75 ～ 13.0
SK13
33
39 ～ 51 45 ～ 60 45 ～ 52 45 ～ 52 45 ～ 52 50 ～ 55 47 ～ 63 55 ～ 75 60 ～ 65
68
SKG13-10HG
HSK 100A
63 77 84 84 74 82 76 91
SKG-12-30L SKG16-10HG SKG16-12HG SKG16-12HG SKG20-12MFHG SKG20-12HG SKG20-18HG SKG-12-30L SKG25-18HGE
- -
- -
2.75 ～ 16.0
SK16
40
116 166
50 55
3.5 ～ 20.0
SK20
116 166 86 111
-
48.5
-
1
7.5 ～ 25.4
SK25
-
55
-
1
★ Collet, adjust screw （ G No. ） and spanner are available as an option. ★ Please refer P.285 for J type nut. The Code No. of the spanner is SK6C （ C= φ 18 ） : SKL-6, SK6C （ C= φ 19.5 ） :SKL-6W, SK10C:SKL-10, SK13C:9HC12A, SK16C:9HC16, SK20C:9HC22, SK25C:9HC25 ★ H 1 means MAX.H without an adjust screw . ★ No adjust screw is applied for the Slim Chucks marked ＊ 3 . ★ All Slim Chucks are High Pressure Centre Through Coolant type （ MAX. 7MPa ） . SK6C ： φ 4 ～ φ 6, SK10C ： φ 6 ～ φ 10, SK16C ： φ 10 ～ φ 16, SK25C ： φ 16 ～ φ 25 ★ Slim Chucks marked ＊ 2 and ＊ 3 can be used for the centre through coolant type with J type nut. ★ is C type. HSK40A-SK16C-120, HSK50A-SK6C-80, HSK63A-SK25C-135 ★ Please refer P.285 for sk Coolant Solution. ★ Lubrication Pipe is optional. Please refer P.298 P.283 for SK collet and please refer
236
Powered by FlippingBook