NC5 MORSE TAPER SLEEVE TYPE A
L
For Drill & Reamer with MT No.1 ～ No.4 Shank.
MT No.
φC
W
MTA
Weight （ kg ）
Weight （ kg ）
MT
C W
TAPER
No.
C W
MT
No.
TAPER
Code No.
Code No.
0.9 1.1 1.3 1.2 1.3 1.6 2.2
5.6 6.6 8.4 5.6 6.6 8.4 12.4
NC5- 46-MTA1- 85 -MTA2- 95 -MTA3-115 NC5- 63-MTA1- 85
MT1 MT2 MT3 MT1 MT2 MT3 MT4
25 32 40 25 32 40 50
NC5- 85-MTA1- 85 -MTA2- 95 -MTA3-115 -MTA4-140 NC5-100-MTA1- 85
25 32 40 50 25 32 40 50
5.6 6.6 8.4 12.4 5.6 6.6 8.4 12.4
2.6 2.7 3.0 3.5 4.1 4.2 4.5 5.1
MT1 MT2 MT3 MT4 MT1 MT2 MT3 MT4
NC5- 46 NC5- 63
NC5-100 NC5- 85
-MTA2- 95 -MTA3-115 -MTA4-140
-MTA2- 95 -MTA3-115 -MTA4-140
★ Please contact with us for the Centre Through Coolant type Sleeve.
NC5 STUB ARBOR
G
L
30
H 1
No Vibration at slotting.
W
φ D
φC
H 2 (3,5,7,8,10,12)
SCA
Code No. （ Inch )
Weight （ kg ）
Code No. （ Metric ） NC5- 63-SCA13-75 -SCA16-75 -SCA22-75 -SCA27-75 -SCA32-90 NC5- 85-SCA13-75 -SCA16-90 -SCA22-90 -SCA27-90 -SCA32-95 NC5-100-SCA13-75
C
W
G
H 1
TAPER
- 3.18(4) 3.18(4) 6.35(7) 7.92(8) - 3.18(4) 3.18(4) 6.35(7) 7.92(8) - 3.18(4) 3.18(4) 6.35(7) 7.92(8) 9.52(10)
NC5- 63-SCA12.7 -75 -SCA15.875-75 -SCA22.225-75 -SCA25.4 -75 -SCA31.75 -90 NC5- 85-SCA12.7 -75
M12 M14 M20 M24 M30 M12 M14 M20 M24 M30 M12 M14 M20 M24 M30 M36
1.2 1.4 1.7 2.0 2.6 2.6 2.8 3.2 3.5 3.9 4.0 4.2 4.4 4.5 4.7 4.9
17 23 29 32 41 17 23 29 32 41 17 23 29 32 41 46
20 26 34 40 46 20 26 34 40 46 20 26 34 40 46 55
NC5- 63
-SCA15.875-90 -SCA22.225-90
NC5- 85
-SCA25.4 -90, 135 -SCA31.75 -90, 135
NC5-100-SCA12.7 -75 -SCA15.875-90 -SCA22.225-90 -SCA25.4 -90
-SCA16-90 -SCA22-90 -SCA27-90 -SCA32-90 -SCA40-90
NC5-100
-SCA31.75 -95, 135 -SCA38.1 -95, 135
★ The “ D ” of Code No. shows shaft diameter. ★ Guide Key and Collars are supplied as standard. ★ The figures in （ ） of W are for Metric.
NC5 TAPPER CHUCK
Tap Collet
L
P. 291, P. 292
Built-in Floating Mechanism and Torque-Limiter Mechanism on Tap Collet.
φ C 1
φ D
φ C
Z
- Compression
Tension +
Tapping Capability
Weight （ kg ）
D
C
Tap Collet
C 1
Code No.
TAPER
M
U
P
P 1/16 ～ 1/4 P 1/8 ～ 3/8 P 1/4 ～ 5/8 P 3/8 ～ 1 P 1/16 ～ 1/4 P 1/8 ～ 3/8 P 1/4 ～ 5/8 P 3/8 ～ 1 P 1 ～ 3 P 1/16 ～ 1/4 P 1/8 ～ 3/8 P 1/4 ～ 5/8 P 3/8 ～ 1 P 1 ～ 3
1/8 ～ 1/2 1/8 ～ 5/8 1/2 ～ 1 3/8 ～ 1 3/8 1/8 ～ 1/2 1/8 ～ 5/8 1/2 ～ 1 3/8 ～ 1 3/8 1 ～ 3 3/4 1/8 ～ 1/2 1/8 ～ 5/8 1/2 ～ 1 3/8 ～ 1 3/8 1 ～ 3 3/4
M 2 ～ M12 M 3 ～ M16 M 8 ～ M24 M18 ～ M38 M 2 ～ M12 M 3 ～ M16 M 8 ～ M24 M18 ～ M38 M36 ～ M100 M 2 ～ M12 M 3 ～ M16 M 8 ～ M24 M18 ～ M38 M36 ～ M100
NC5- 63-Z12- 90 -Z16-120 -Z24-120 -Z38-160 NC5- 85-Z12-105 -Z16-120 -Z24-120 -Z38-175 -Z65-195 NC5-100-Z12-130
1.5 2.0 2.1 6.7 3.3 4.5 4.9 8.4 8.7 4.3 5.2 5.8 8.3 9.0
32 39 46 78 32 39 46 78 110(125) 32 39 46 78 110(125)
19 25 30 45 19 25 30 45 68 19 25 30 45 68
45 55 68 85 45 55 68 85 110 45 55 68 85 110
ZKG 12 ZKG 16 ZKG 24 ZKN 38 ZKG 12 ZKG 16 ZKG 24 ZKN 38 ZKN 65 ZKG 12 ZKG 16 ZKG 24 ZKN 38 ZKN 65
NC5 - 63
NC5 - 85
-Z16-135 -Z24-125 -Z38-155 -Z65-195
NC5 - 100
★ Please refer
P.291, P.292 for Tap Collet. ★ For Synchronized Tapping : ZH Tapper Chuck without tension/compression mechanism is available. It improves tap life remarkably by absorbing fine pitch error completely with the small floating mechanism. Please use ZH Tapper Chuck only with ZMK Tap Collet without torque-limiter mechanism. Please refer P.296. ★ Centre through coolant type with high pressure or oil mist type is available. In these types, OZMK-OM collet is used.
NC5- 63-ZH12- 90 -ZH24-105 NC5- 85-ZH12- 90 -ZH24-105
NC5-100-ZH12- 90 -ZH24-105
ZH Tapper Chuck ＋ ZMK Tap Collet
225
Powered by FlippingBook