NC5 VEGA CHUCK
New Innovation for High Speed Milling The setting of cutter can be done through the centre hole of the pull stud with wrench.
L
Run-out within 3 μ m
PMK Collet VMK Collet
ℓ
φD
φD φC
4D
VMC
Chucking Range φ D
MAX. （r/ min ）
Weight （ kg ）
ℓ
Collet Removal Jig
Collet
C
Code No.
TAPER
2 ～ 8 4 ～ 12 4 ～ 16 6 ～ 20 8 ～ 25 2 ～ 8 4 ～ 12 4 ～ 16 6 ～ 20 8 ～ 25 12 ～ 32 2 ～ 8 4 ～ 12 4 ～ 16 6 ～ 20 8 ～ 25 12 ～ 32
NC5- 63-VMC 8- 60, 120N -VMC12- 65, 120 -VMC16- 85, 120 -VMC20- 85, 120 -VMC25- 90, 120 NC5- 85-VMC 8- 75N, 135 -VMC12- 75, 135 -VMC16- 85, 135 -VMC20- 85, 135 -VMC25- 90, 135 -VMC32-110 NC5-100-VMC 8- 90N, 150N
22 30 40 47 55 22 30 40 47 55 70 22 30 40 47 55 70
PMK 8, VMK 8J PMK12, VMK12J VMK16, VMK16J VMK20, VMK20J VMK25, VMK25J PMK 8, VMK 8J PMK12, VMK12J VMK16, VMK16J VMK20, VMK20J VMK25, VMK25J VMK32, VMK32J PMK 8, VMK 8J PMK12, VMK12J VMK16, VMK16J VMK20, VMK20J VMK25, VMK25J VMK32, VMK32J
30, 30 35, 47 53, 88 53, 88 60, 90 30, 30 39, 42 47, 57 47, 97 52, 97 72 30, 30 49, 60 49, 80 42, 95 47, 107 57
1.1,1.4 1.2,1.7 1.4,1.8 1.5,2.0 1.7,2.3 2.3,2.7 2.4,2.9 2.5,3.3 2.6,3.3 2.8,3.6 3.6 4.0,4.5 4.1,4.6 4.2,4.9 4.2,5.3 4.3,5.4 4.9
NC5- 63
VML-63
40,000
NC5- 85
VML-85
20,000
-VMC12- 90, 150 -VMC16- 90, 150 -VMC20- 85, 150 -VMC25- 90, 150 -VMC32-105
NC5-100
VML-100
20,000
★ The “ D ” of the Code No. shows MAX. gripping diameter. ★ Please add “ P ” at the end of Code No. for High Speed Chuck. e.g. NC5-63-VMC16-85P.
★ Collet and collet removal jig are available as an option.
VMK Collet Code No. VMK 8- 2J, 3J, 4J, 5J, 6J, 8J VMK12- 4J, 5J, 6J, 8J, 10J, 12J VMK16- 4J, 5J, 6J, 8J, 10J, 12J, 16J VMK20- 6J, 8J, 10J, 12J, 16J, 20J VMK25- 8J, 10J, 12J, 16J, 20J, 25J VMK32- 12J, 16J, 20J, 25J, 32J
Collet Removal Jig VML
Push back the Pull Stud onto the VEGA Chuck and rotate the Chuck to tighten and release. Spanner is available as an option. NC5-53, NC5-63 ： 9HC22, NC5-85 ： 9HC32, NC5-100 ： 9HC42
Releasing PROTECTION MUST BE USED.
Tightening
★ Please note the acceptable shank tolerance is h8. ★ VMK8 -2J is Jet Spread Hole type.
NC5 ANNIVERSARY TYPE VC HOLDER
G No. （ Option ） L H
With TiN Bearing Nut MAX.40,000r/min Run-Out Accuracy ： 3 μ m at 4D
φC
φC 1
φD
ℓ
ℓ 1
L L
VC
JAPAN, USA, EU, KOREA PAT.
Weight （ kg ） 0.5,0.6,0.8 0.8,0.9,1.2 1.3,1.5,1.7 1.4,1.7,2.1 2.6,2.8,3.1 2.8,3.2,3.6 4.3,4.5,4.9 4.5,4.9,5.3
MAX. （r/ min ）
G No. （ Option ）
ℓ ℓ 1
TAPER
Code No.
D L
C C 1
H
Collet
2.0 ～ 6.0 3.0 ～ 12.0 2.0 ～ 6.0 3.0 ～ 12.0 2.0 ～ 6.0 3.0 ～ 12.0 2.0 ～ 6.0 3.0 ～ 12.0
-,-,35 ～ 45 -,-,50 ～ 60 35 ～ 45 -,50 ～ 60,50 ～ 60
VCK 6 VCK13 VCK 6 VCK13 VCK 6 VCK13 VCK 6 VCK13
27.5,31.7,33.4 41.8,41.3,42.4 30.0,32.7,36.9 40.3,44.3,48.5 33.7,37.8,42.0 45.3,49.5,53.7 33.0,37.1,41.3 44.6,48.8,53.0
45,60,90 65,90,120 60,90,120
23 29 23 29 23 29 23 29
23,35,65 42,67,97 30,60,90 31,60,90 67,97,127
28 40 28 40 28 40 28 40
-,-,VCG 6- 8A -,-,VCG13-15A VCG 6- 8A -,VCG13-15A,VCG13-15A
NC5- 46-VC 6- 45, 60, 90 -VC13- 65, 90, 120 NC5- 63-VC 6- 60, 90, 120 -VC13- 60, 90, 120 NC5- 85-VC 6-105, 135, 165 -VC13-105, 135, 165 NC5-100-VC 6-105, 135, 165 -VC13-105, 135, 165
NC5- 46 NC5- 63 NC5- 85 NC5-100
40,000
30,000
35 ～ 45 50 ～ 60 35 ～ 45 50 ～ 60
VCG 6- 8A VCG13-15A VCG 6- 8A VCG13-15A
20,000
105,135,165
20,000
62,92,122
105,135,165
★ Collet, adjust screw （ G No. ） and GH Handle are available as an option. ★ Please refer P.285 for JET Coolant Splash with J type Nut . The Code No. of the GH Handle is VC6: GH10, VC13: GH16 ★ When the axial stopper is required, please use Adjust Screw （ G No. ） ★ Please add “ -RP ” at the end of Code No. for Rust Proof Treatment VC Holder. e.g : NC5-63-VC13-60-RP ★ Please use VC J type Nut & Cap for Centre Through Coolant. When VC J type Nut is used, the total holder length will be extended to 6mm. ★ NC5-63-VC 6-150, NC5-63-VC13-150, NC5-100-VC13- 90, -120 are available as semi-standard. ★ All series are for High Speed Rotation.
VCK Collet Code No.
VCK 6 -2, 3, （ 3.175 ） , 4, 5, 6 VCK13 -3, （ 3.175 ） , 4, 5, 6, 7, 8, 9, 10, 11, 12
★ Please note the acceptable shank tolerance is h 8 . ★ Inch size is also available. VCK6-1/8, 3/16, 1/4 VCK13-1/8, 3/16, 1/4, 5/16, 3/8, 7/16, 1/2 ★ VCK6-3.175 and VCK13-3.175 are same as VCK6-1/8 and VCK13-1/8 respectively. Please order VCK6-1/8 or VCK13-1/8
218
Powered by FlippingBook