NC5 MILLING CHUCK
ℓ 1
ℓ 2
Stopper Weight （ kg ）
Code No.
D 1
D 2
L
TAPER
Collet
NC5-100-C12-105 -C16-105
105 105 135 165 200
56
46
4.1 4.4 4.7 5.0 5.3 4.6 5.5 5.8 5.0 6.1 6.4 4.8 5.4 7.1 7.5 5.5 6.1 8.6 9.0̶
33
12
KM12 CCK12
-135 -165 -200 -C20-105 -165 -200 -C25-105 -165 -200 -C32- 90 -105 -165 -200 -C42- 95 ＊
65
49
44
16
KM16 CCK16
57
52
20
9MC20H
KM20
NK20 CCNK20 CCK20
105 165 200
80
NC 5 - 100
60
60
25
9MC25H
KM25
CCNK25 CCK25 NK25
90 105 165 200 95 115 165 200
9MC32HS 9MC32H 9MC32H 9MC32H̶ 9MC42HS 9MC42H 9MC42H
70
69
81
32
KM32
CCNK32 CCK32 NK32
105 125 125 125
-115 -165 -200
73
86
42
KM42
CCNK42 CCK42 NK42
★ For High Speed type, please add “ G ” at the end of Code No. e.g.NC5-63-C16-60G ★ Spanner is available as an option. C12 ： 9HC12A, C16 ： 9HC16, C20 ： HC20, C25 ： 9HC25, C32 （ φ 64 ） ： 9HC25, C32 （ φ 69 ） ： 9HC32, C42 ： 9HC42 ★ NC5-63-C32-80 may not be used by the M/C restriction. ★ Milling Chuck for Oil Mist is also available. Please contact with us. ★ CCNK collet and the stopper can not be used for the chucks marked ＊ . The cutter shank length must be longer than ℓ 2 in case of the direct chucking and centre through coolant application. ★ CCNK collet can be used for the all chucks except marked ＊ . The stopper （ optional accessory ） is required, if the cutter shank length is shorter than ℓ 2 and direct chucking, ★ The “ D 1 ” in the Code No. shows ID of the chuck. ★ Please note the acceptable shank tolerance is h7. ★ Please refer P.281 for KM, CCK, CCNK Collet. Stopper for Direct Chucking Direct chucking means that chucking φ 32mm shank tool into φ 32mm ID chuck. If tool shank length is longer than R 1 , the stopper is not required. C12 and C16 Milling Chuck with Special Stopper C12 and C16 Milling Chucks with the stopper to use with KM Collets are available as special option. e.g. NC5-63-C12-65S, NC5-63-C16-70S
ℓ 1
Stopper 9MC20H 9MC20HS 9MC25H 9MC32H 9MC32HS 9MC42H
Chuck C20C C25C C32C C42
H 1 42 ～ 47 50 ～ 55 49 ～ 59 55 ～ 60 57 ～ 67
C 2 17 22 24 24
H 1
KM 12 Collet KM 16 Collet
O-ring
φ D
C 2
O-ring
Stopper C 12 ： MCG 12 - 6 HG C 16 ： MCG 16 - 6 HG
C12 ： 41.5 ～ 46.5 C16 ： 49 ～ 54
Oil hole pitch ★ For heavy milling, please insert the cutter shank longer than ℓ 1 into the chuck body. Do not use the stopper. ★ When the oil hole pitch of the back end is larger than the dia. of O-ring, please contact with us.
For the types with O-ring on the end flange add the O-ring type at end of the Code No. e.g. MCG16-6HG-S6 For the steel type, add “ -FE ” at the end of Code No. e.g. MCG16-6HG-FE
High Speed Milling Chuck Please add “ G ” at the end of Code No. for High Speed Milling Chuck.
MAX. （r/ min ）
MAX. （r/ min ）
Code No.
Code No.
TAPER
TAPER
NC5-100-C12-105G -C16-105G -C20-105G -C25-105G -C32- 90G -C42- 95P NC5- 85-C12- 80G -C16- 80G -C20- 80G -C25- 80G -C32- 85G -C42-105P
NC5- 46-C12- 55G -C16- 70G -C20- 80G -C25- 90G -C32-100G
40,000 30,000 20,000 10,000
GH Handle
P.299
15,000
NC5-46
NC5-85
＊
12,000
＊
NC5- 63-C12- 65G
＊ -C16- 60G, 70G -C20- 70G, 80G -C25- 70G, 90G -C32- 80G , 90G
20,000
15,000
★ The extended tool length is available as an option. Please contact with us. ★ The stopper can not be used for the chucks marked ＊ . The cutter shank length must be longer than ℓ 2 in case of the direct chucking and centre through coolant application. ★ All chucks except marked ＊ can be used for high pressure centre through coolant application. The stopper （ optional accessory ） is required, if the cutter shank length is shorter than ℓ 2 and direct chucking.
NC5-63
NC5-100
15,000
12,000
＊
★ GFS type
P.33 is available for C25 and C32 except NC5-46 shank.
Face Seal type （ for Alminium cutting ） GFS
JAPAN PAT.
216
Powered by FlippingBook